+- Vgate Forums (https://forum.vgatemall.com)
+-- Forum: Vgate OBD (https://forum.vgatemall.com/forumdisplay.php?fid=28)
+--- Forum: vLinker Series (https://forum.vgatemall.com/forumdisplay.php?fid=30)
+---- Forum: Vgate vLinker FS USB (https://forum.vgatemall.com/forumdisplay.php?fid=37)
+---- Thread: Help me for Opel Karl 2016!!! (/showthread.php?tid=8410)
Help me for Opel Karl 2016!!! - Ellenico - 10-14-2024
Sorry for my bad english.
I use AlfaOBD or Multiecuscan for Fiat Panda 2006, and i can enter all the control units and change the settings; I use Vgate Vlinker FS, Vgate Icar Pro 2S and all the colored adapters for Fiat.
Now, with Vgate Icar Pro 2S and software (OPL Monitor or ScanMyOpelCan) i can read and erase only errors code DTC, but it's impossible change settings as for my Fiat Panda using MUltiecuscan or AlfaOBD (Proxy Alignment, ABS, Instrument, etc). And for Vgate Vlinker FS, I didn't find any program for Windows 11.
You Could make some adapter for Vgate Vlinker FS to make it compatible with GM GDS2 for exemple? This program for full operation diagnosing GM vehicles using a J2534 adapter is required that supports CAN bus 6-14, 3-11, 12-13 contacts of the OBD2 connector, as well as a single wire CAN bus on Pin1.
If you make a compatible adapter for my Vlinker FS, i'm the first to buy them. If you have any advice for me on what software to use on windows11 and Vlinker FS for my Opel Karl, I world be happy...Thank You.
RE: Help me for Opel Karl 2016!!! - Ellenico - 10-16-2024
No support?
RE: Help me for Opel Karl 2016!!! - admin - 10-17-2024
(10-14-2024, 09:49 AM)Ellenico Wrote: Sorry for my bad english.
I use AlfaOBD or Multiecuscan for Fiat Panda 2006, and i can enter all the control units and change the settings; I use Vgate Vlinker FS, Vgate Icar Pro 2S and all the colored adapters for Fiat.
Now, with Vgate Icar Pro 2S and software (OPL Monitor or ScanMyOpelCan) i can read and erase only errors code DTC, but it's impossible change settings as for my Fiat Panda using MUltiecuscan or AlfaOBD (Proxy Alignment, ABS, Instrument, etc). And for Vgate Vlinker FS, I didn't find any program for Windows 11.
You Could make some adapter for Vgate Vlinker FS to make it compatible with GM GDS2 for exemple? This program for full operation diagnosing GM vehicles using a J2534 adapter is required that supports CAN bus 6-14, 3-11, 12-13 contacts of the OBD2 connector, as well as a single wire CAN bus on Pin1.
If you make a compatible adapter for my Vlinker FS, i'm the first to buy them. If you have any advice for me on what software to use on windows11 and Vlinker FS for my Opel Karl, I world be happy...Thank You.
There is no programmable application on the open car market, the only one that can be supported is the J2534
There is no programmable application on the open car market, only the J2534 is supported.
About Multiecuscan iCar Pro 2S can't be supported, because iCar Pro 2S is used to read car data, not for programming, and the protocol support is very little.